advanced power electronics corp. ape8902c 2a ultra low dropout linear regulator features description ultra low dropout 0.21v(typical) @ 2a output current for 1.2v output voltage low esr output capacitor (multi-layer chip capacitors (mlcc)) applicable en pull-low for ape8902cmp-a en pull-high for ape8902cmp-b fast transient response adjustable output voltage by external resistors power-on-reset monitoring on both vcntl and vin pins internal soft-start current-limit and thermal shutdown protection power-ok output with a delay time so-8 with exposed pad & dfn 3x3-10l pb-free package. halogen free product data and specifications subject to change without notice 20130206v4.1 typical application 1 the ape8902c series is a 2a ultra low dropout linea r regulator. this product is specifically designed to provide well supply voltage for front-side-bus termination on motherboards and nb applications. the ic needs two supply voltages, a control voltage for the circuitry and a main supply voltage for power conversion, to reduce powe r dissipation and provide extremely low dropout. the ape8902c series integrates many functions. a power-on- reset (por) circuit monitors both supply voltages to prevent wrong operations. a thermal shutdown and current limit functions protect the device against thermal and current over-loads. a pok indicates the output status with time delay which is set internally. it can control othe r converter for power sequence. the ape8902c series can be enabled by other powe r system. pulling and holding the en pin below 0.4v shuts of f the output. the ape8902c series is available in esop-8 package which features small size as so-8 and an exposed pad to reduce the junction-to-case resistance, being applicable in 2~3w applications. pok en vin vcntl nc vout adj gnd ape8902c u1 1uf c2 4.7uf c1 10k r3 20k r1 10k r2 10uf cout pok en *option cf v out v in v cntl
advanced power electronics corp. ape8902c absolute maximum ratings (note1) cntl supply voltage (v cntl ) -------------------------- - -0.3v to 6.5v input supply voltage (v in ) ------------------------------ - -0.3v to 6.5v en & fb pin voltage (v en /v fb ) ------------------------ - -0.3v to vcntl+0.3v power good voltage (v pok ) --------------------------- - -0.3v to 6.5v power dissipation (p d ) --------------------------------- - 2.5w storage temperature range (t st ) ------------------- - -65c to 150c junction temperature range (t j ) -------------------- - -40c to 150c esop-8 ------ - 40c/w dfn 3x3-10l 62.5c/w thermal resistance junction to case (rth jc ) note. esop-8 ------ - 15c/w dfn 3x3-10l 17c/w note. mounted on a demo board recommended operating conditions operating junction temperature range (t oj ) ---- - -40c to 125c operating ambient temperature range (t oa ) ---- - -40c to 85c vcntl supply voltage (v cntl ) ------------------------ - 3v to 6v input supply voltage (v in ) ------------------------------ - 1.1v to 5.5v output voltage (v out )@v cntl > v out + 2.5v ------ - 0.8v to 2.8v output cunrrent (i out ) ----------------------------------- - 0a to 2a package/ordering informatio n 2 thermal resistance junction to ambient (rth ja ) note. ( top view ) 1 2 3 4 8 7 6 5 nc vout esop-8 gnd fb en pok vin vcntl gnd ( top view ) 1 2 3 4 8 7 6 dfn 3x3-10l gnd 5 9 10 vout vout vout fb pok en vin vin vin vcntl package type mp : esop-8 gn3 : dfn 3x3-10l ape8902cx-x en function a : internal pull low b : internal pull high
advanced power electronics corp. ape8902c electrical specifications v cntl = 5v, v in =1.8v, v out =1.2v, t a =25 o c unless otherwise specified parameter sym test condition min typ max units v cntl operation voltage v cntl 2.8 - 5.5 v v in por threshold v in 0.8 0.9 1 v v in por hysteresis v in(hys) - 0.5 - v v cntl nominal supply current i cntl en= v cntl - 1.3 - ma ape8902cmp-a - - 1 ape8902cmp-b - 10 30 v cntl =3 ~ 6v, i out =10ma, v in =v out +0.5~5.5v load regulation i out =0a ~ 2a - 0.5 1 % i out =100ma, v cntl =v en =5.0v, v out =1.2v dropout voltage v drop i out = 2a, v cntl =5v, v out = 1.2v - 0.21 0.3 v v out pull low resistance en=0v - 40 - soft start time t ss - 0.2 - ms v enh enable 1.2 - - v enl disable - - 0.6 en=5v, ape8902cmp-a - 10 20 en=gnd, ape8902cmp-b - 10 20 current limit i lim v cntl =5v, v in =v out +1v 2.5 - - a -65- -65- pok threshold voltage for power ok v pok vfb rising 92% 94% 96% v fb pok threshold voltage for power not ok v pnok vfb falling 83% 88% 91% v fb pok low voltage pok sinks 5ma - - 0.1 v pok delay time t delay 0.8 2 10 ms thermal shutdown threshold (note1) t sd - 160 - o c thermal shutdown hysteresis (note1) -40- o c note1: guarantee by design, not production tested. 105 0.8 3 v 0.816 v 150 m db ua en pin logic high threshold voltage on resistance r ds(on) vcntl shutdown current i sd ua feedback voltage v fb 0.784 f=120hz, i out =100ma ripple rejection psrr en pin pull-up current i en - v in v cntl en=0v
advanced power electronics corp. ape8902c pin descriptions pin symbol pin description pok power ok output pin internal pull high (ape8902cmp-b) or pull low (ape8902cmp-a) en=high or floating enable en=low shutdown mode vin power input pin of the control circuitry. the pin is monitored for power-on reset purpose. nc no connect vout output voltage fb feedback pin gnd gnd pin block diagram ape8902cmp-a ape8902cmp-b 4 en supply input for power conversion. the pin is monitored for power-on reset purpose. vcntl -+ vin vout gnd error amp en vcntl soft -start and control logic power- on reset current limit thermal shutdown bandgap fb -+ pok delay pok 94% v ref n-mosfet 10ua enable -+ vin vout gnd error amp en vcntl soft -start and control logic power- on reset current limit thermal shutdown bandgap fb -+ pok delay pok 94% v ref n- m o s f et 10ua enable
advanced power electronics corp. ape8902c pin description fb vin vcntl pok en vout function description power-on-reset internal soft-start output voltage regulation 5 connecting this pin to an external resistor divider receives the feedback voltage of the regulator. the output voltage set by the resistor divider is determined by: a power-on-reset (por) circuit monitors both input voltages at vcntl and vin pins to prevent wrong logic controls. the por function initiates a soft-start process after the two supply voltages exceed their rising por threshold voltages during powering on. the por function also pulls low the pok pin regardless the output voltage when the vcntl voltage falls below its falling por threshold. an internal soft-start function controls rise rate of the output voltage to limit the current surge at start-up. the typical soft-start interval is about 0.2ms. an error amplifier working with a temperature compensated 0.8v reference and an output nmos regulates output to the preset voltage. the error amplifier designed with high bandwidth and dc gain provides very fast transient response and less load regulation. it compares the reference with the feedback voltage and amplifies the difference to drive the output nmos which provides load current from vin to vout. where r1 is connected from vout to fb with kelvin sensing and r2 is connected from fb to gnd. a bypass capacitor may be connected with r1 in parallel to improve load transient response. the r2 range in 1k~4.7k for al output capacitor and 30k~100k for mlcc output capacitor are recommended. power input pin of the control circuitry. connecting this pin to a +5v (recommended) supply voltage provides the bias for the control circuitry. the voltage at this pin is monitored for power- on reset purpose. power-ok signal output pin. this pin is an open-drain output used to indicate status o f output voltage by sensing fb voltage. this pin is pulled low when the rising fb voltage is not above the vpok threshold or the falling fb voltage is below the vpok threshold, indicating the output is not ok. enable control pin. pulling and holding this pin below 0.4v shuts down the output. when re- enabled, the ic undergoes a new soft-start cycle. for ape8902cmp-b, this pin is internal pulled up to vcntl voltage, enabling the regulator. for ape8902cmp-a, this pin is internal pulled down to gnd voltage, shutdown the regulator. the pull-high current is 10ua (typ.) output of the regulator. please connect pin 6 using wide tracks. it is necessary to connect an output capacitor with this pin for closed-loop compensation and improving transient responses. main supply input pins for power conversions. the voltage at this pin is monitored for power- on reset purpose.
advanced power electronics corp. ape8902c function description current-limit thermal shutdown application information capacitor selection 6 a thermal shutdown circuit limits the junction temperature of ape8902c. when the junction temperature exceeds +160c, a thermal sensor turns off the output nmos, allowing the device to cool down. the regulator regulates the output again through initiation of a new soft-start cycle after the junction temperature cools by 40 c, resulting in a pulsed output during continuous thermal overload conditions. the thermal shutdown designed. normally, use a mlcc capacitor on the input and output of the ape8902c. larger input capacitor values provide better supply-noise rejection and transient response. a higher- value output capacitor may be necessary if large, fast transients are anticipated and the device is located several inches from the power source. the x5r and x7r type in mlcc is recommended. for aluminum electrolytic capacitor application, 100uf in input capacitor and 220uf in output capacitor (30m < esr < 200m ) are recommended. output capacitor of larger capacitance can reduce noise and improve load transient response, stability, and psrr. the ape8902c monitors the current via the output nmos and limits the maximum current to prevent load and ape8902c from damages during overload or short circuit conditions.
advanced power electronics corp. ape8902c typical performance characteristics line regulation dropout voltage at v cntl =5v dropout voltage at v cntl =3.3v i cntl vs. t j i cntl-sd (ape8902cmp-b) vs. t j 7 load regulation 0.780 0.785 0.790 0.795 0.800 0.805 0.810 0.815 0.820 3 3.4 3.8 4.2 4.6 5 v cntl (v) v o (v) io=0ma io=1a 0.0 0.5 1.0 1.5 2.0 2.5 3.0 -40 -20 0 20 40 60 80 t j (c) i cntl (ma) 0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0 -40 -20 0 20 40 60 80 t j (c) i cntl-sd (ua) 0 50 100 150 200 250 300 350 400 450 500 0 0.5 1 1.5 2 i out (a) v drop (mv) vo=2.5v vo=1.8v vo=1.2v vo=1.05v 0 100 200 300 400 500 600 700 0 0.5 1 1.5 2 i out (a) v drop (mv) vo=1.2v vo=1.05v 0.75 0.76 0.77 0.78 0.79 0.80 0.81 0.82 0.83 0.84 0.85 0 0.5 1 1.5 2 i out (a) v o (v)
advanced power electronics corp. ape8902c typical performance characteristics 8 en on with pok delay vin power ?on v fb vs. t j v en vs. t j 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 -40 -20 0 20 40 60 80 t j (c) v en (v) venh venl 0.70 0.72 0.74 0.76 0.78 0.80 0.82 0.84 0.86 0.88 0.90 -40 -20 0 20 40 60 80 t j (c) v fb (v) v en v out pok i out =2a v en v out pok i out =2a
advanced power electronics corp. ape8902c marking information esop-8 dfn 3x3-10l 9 part number date code (ywwsss) y last digit of the year ww week sss sequence package code 8902cmp-x ywwsss en function 8902c-x ywws part number en function date code (ywws) y last digit of the year ww week s sequence
|
